The best and most updated latest Cisco CCDP 300-101 dumps exam training resources in PDF format download free try from leads4pass. Cisco CCDP 300-101 dumps exam preparation kit contains all the necessary 300-101 questions that you need to know. “Implementing Cisco IP Routing” is the name of Cisco CCDP https://www.leads4pass.com/300-101.html exam dumps which covers all the knowledge points of the real Cisco exam. High quality Cisco CCDP 300-101 dumps vce youtube demo update free shared. If you are looking to get Cisco Implementing Cisco IP Routing certification by passing exam 300-101 then you can pass it in one go.
Download free latest Cisco 300-101 dumps pdf: https://drive.google.com/open?id=0B_7qiYkH83VRWFlVNGtTZjU1MVE
Download free latest Cisco 400-101 dumps pdf: https://drive.google.com/open?id=0B_7qiYkH83VRQ1BCdmJuZzdZN0U
Cisco CCDP 300-101 Dumps Exam Questions And Real Answers (1-34)
QUESTION 1
Features of Netflow version 9? (choose two)
A. IEEE standard
B. IETF standard
C. ingress only
D. egress only
E. ingress/egress
Correct Answer: BE
QUESTION 2
How route tags can be set?(choose two)
A. ONLY within route tags
B. within taglists
C. can be set with ONLY route-maps
D. can be set DIRECTLY within route maps.
E. only used on link state RPs
Correct Answer: BD
QUESTION 3
Which condition can cause unicast reverse path forwarding to fail?
A. split horizon
B. STP convergence
C. PortFast security violation
D. asymmetric routing
Correct Answer: D
QUESTION 4
Which set of actions does a network engineer perform to set the IPv6 address of a DHCP relay server at the VLAN interface level?
A. Enter the VLAN interface configuration mode and define the IPv6 address of a DHCP relay server
B. Enter the global configuration mode and enable the IPv6 DHCP relay
C. Enter the global configuration mode, enable IPv6 DHCP relay from interface configuration mode and define the IPv6 address of a DHCP relay server
D. Enter the VLAN interface configuration mode, enable IPv6 DHCP relay, and define the IPv6 address of a DHCP relay server
Correct Answer: D
QUESTION 5
which two types of authentication dose EIGRP offer ?(choose two)
A. TKIP
B. MD5
C. WPA
D. Plain text
Correct Answer: BD
QUESTION 6
Refer to the following
Logging Console7
Which option is one of the effects entering this command on a Cisco IOS router, with no additional logging configuration?
A. Debug messages can be seen on the console by enabling “terminal monitor.”
B. Debug messages are logged only on active console connections.
C. A user that is connected via SSH sees level 7 messages
D. The router can experience high CPU utilization
Correct Answer: D
QUESTION 7
Which two options can you use to configure an EIGRP stub router? 300-101 dumps (Choose two)
A. summary-only
B. receive-only
C. external
D. summary
E. totally-stubby
F. not-so-stubby
Correct Answer: BD
QUESTION 8
After configuring the routes, the network engineer executes the show ip route command. What is the expected results?
A. Gateway of last resort is 10.0.2.1 to network 0.0.0.0 10.0.0.0/24 is subnetted, 2 subnets C 10.0.2.0is directly connected, FastEthernetO/O 10.0.1.0 is directly connected, FastEthernet0/l S”0.0.0.0/0[1/0] via 10.0.2.1(1/0] via 10.0.1.1
Router#
B. Gateway of last resort is 10 0.2 1 to network 0 0 00 10 0.0 0/24 is subnetted, 1 subnet C 10.0.2 isdirectly connected, FastEthernetO/O S 0.0.0 0/0 [1/0] via 10.0.2.1
Router#
C. Gateway of last report is not set
Router #
D. Gateway of test resort is 10.0.1.1 to network 0.0.0.0 10.0.0.0/24 is subnetted 1 subnet C 10.0.1.0 is directly connected FastEthernetO/1 S” 0.0.0?/0 [1/0] via 10.0.1.1
Router#
Correct Answer: C
QUESTION 9
Which two statements about NTP stratum are true? (Choose two )
A. Stratum 15 indicates a device that is not synchronized
B. Stratum 1 devices receive their time from a peer that is connected directly to an authoritative time source.
C. The highest stratum level a synchronized device can have is 16
D. Stratum 2 devices receive their time from a peer that is connected directly to an authoritative time source
E. Stratum 0 devices are connected directly to an authoritative time source
F. Stratum 1 devices are connected directly to an authoritative time source
Correct Answer: DF
QUESTION 10
Which technology dose Easy virtual network use?
A. MP-BGP
B. DMVPN
C. MPLS
D. VRF-Lite
Correct Answer: D
QUESTION 11
Which two statements about OSPF E1 routes are true? (Choose two)
A. They are preferred over interarea routes
B. They use the OSPF cost from redistribution and the OSPF cost to the ASBR
C. They are preferred over E2 routes
D. They use only the OSPF cost to the ASBR
E. They use only the OSPF cost from redistribution
Correct Answer: BC
QUESTION 12
A senior network engineer tries to propagate a summary route 209.165.201.0/27 to R2 by redistributing static route on Rl, but setup is not working. What is the issue with the configuration in the exhibit.
A. The summary route is in the global routing table.
B. The wildcard bit in network command is incorrect.
C. The redistribute command is in the wrong address-family.
D. The route target is missing
Correct Answer: A
QUESTION 13
Which command denies the default route?
A. ip prefix-list deny-route seq 5 deny 0.0.0.0/32
B. ip prefix-list deny-route seq 5 deny 0.0.0.0/8
C. ip prefix-list deny-route seq 5 deny 0 0 0.0/0
D. ip prefix-list deny-route seq 5 deny 0.0.0.0/16
Correct Answer: C
QUESTION 14
Base on the output, which option is the next hop to get to the 130.0.1.0/24 network?
A. 10.30.30.1
B. 10.0.11.1
C. 10.20.20.1
D. 10.10.10.1
Correct Answer: B
QUESTION 15
Which feature can mitigate fragmentation issues within network segments that are between GRE endpoints?
A. PMTU
B. ICMP DF bit
C. TCP Flow Control
D. TCP MSS
Correct Answer: B
QUESTION 16
The excerpt was taken from the routing table of router SATX. 300-101 dumps Which option ensures that routes from 51.51.51.1 are preferred over routes from 52.52.52.2?
A. SATX(config-router)#distance 90 51.51.51.10.0.0.0
B. SATX(config-router)#distance 89.52.52.52.2 0.0.0.0
C. SATX(config-router)#distance 90.52.52.52.2 0.0.0.0
D. SATX(config-router)#administrative distance 91 51.51.510.0.0.0
E. SATX(config-router)#distance 89 51.51.51.10.0.0.0
F. SATX(config-router)#administrative distance 91 52.52.52.2 0.0.0.0
Correct Answer: B
QUESTION 17
Which Cisco Express Forwarding table or tables hold forwarding information?
A. FIB table only
B. adjacency tables only
C. FIB and adjacency tables only
D. FIB,RIB, and adjacency tables
Correct Answer: C
QUESTION 18
router eigrp 65535
no auto-summary
network 10.0.0.0 0.0.0.255
router ospf 1
network 192.168.5.0 0.0.0.255 area 0
passive-interface loopback0
redistribute eigrp 65535
If this configuration is applied to a device that redistributes EIGRP routes into OSPF. Which two statements about the behavior of the device are true? (Choose two)
A. EIGRP routes appears in the routing table as E2 OSPF routes
B. The device router ID is set to Loopback0 automatically
C. The device redistributes all EIGRP networks into OSPF
D. EIGRP routes appears in the routing table as N2 OSPF routes
E. The device redistributes only classful EIGRP networks into OSPF.
F. EIGRP routes appears as type 3 LSAs in the OSPF database.
Correct Answer: AE
QUESTION 19
A network engineer has configured NTP on a Cisco router, but the time on the router is still incorrect.
What is the reason for this problem?
A. The router is not syncing with the peer, even though the NTP request and response packets are being exchanged.
B. The router is not syncing with peer, and the NTP request and response packets are not being exchanged.
C. The router is syncing with the peer, and the NTP request and response packets are being exchanged.
D. The router is dropping all NTP packets.
Correct Answer: A
QUESTION 20
Which two technologies can encapsulate an IPv6 payload in an IPv4 packet for transmission across a network? (Choose two)
A. L2TPv3
B. trunking
C. AToM
D. ISATAP
E. NAT-PT
Correct Answer: DE
QUESTION 21
Which command do you enter to filter only routing updates that are sent through interface GigabitEthemet0/0?
A. R1(config-if)#passive-interface GigabitEthemet0/0
B. R1(config-router)#no passive-interface GigabitHthemet0/0
C. R1config-router)#passrve-interface GigabitEthemet0/0
D. R1(conffg-router)passive-interface default
E. R1(config-if)#passive-interface default
F. R1(config-router)#distribute-list 1 GigabitEthemet0/0 out
Correct Answer: C
QUESTION 22
A network engineer is unable to make VRF lite EIGRP adjacency work.There is nothing wrong with communication between R1 and R2. What command will eliminate the issue when executed on both routes?
A. (config-router-if)autonomous-system 100
B. (config)#ip-multicast-routing
C. (config-vrf)#route-target both 100:1
D. (config-router-af)#network 209.165.202.128 0.0.0.31
Correct Answer: A
QUESTION 23
What does the number 16 in the following command represent?
Router(config)#snmp-server user abed public v2c access 16
A. the mask of the files that are allowed to use community string public
B. the standard named access list 16, which contains the access rules that apply to user abed.
C. the number of concurrent users who are allowed to query the SNMP community
D. the user ID that is allowed to use the community string public
Correct Answer: B
QUESTION 24
Which value does a point-to-point GRE tjunnel use to identify a peer?
A. MAC address
B. configured multicast address.
C. DLCI
D. IP address
E. VC ID
Correct Answer: D
QUESTION 25
Which two statements about uRPF are true? (Choose two)
A. The Keyword any can be used with both strict mode and loose mode
B. Strict mode may drop legitimate traffic.
C. tt is enabled globally.
D. Strict mode is most appropriate for networks with asymmetric routing.
E. Loose mode may drop traffic when asymmetric routing occurs on the network
F. It is enabled on a per interface basis.
Correct Answer: BF
QUESTION 26
A network engineer is configuring a DHCP server to support a specialized application. Which additional DHCP feature must be enabled to support the delivery of various additional parameters to DHCP clients?
A. modules
B. vendor extensions
C. options
D. Scopes
Correct Answer: C
QUESTION 27
In SNMP v3, which security level provides encryption of the data?
A. authMember
B. noAuthNoPriv
C. authNoPriv
D. authPriv
Correct Answer: D
QUESTION 28
Which three functionalities are specific to stateful NAT64? (Choose Three)
A. It requires IPv4-transalable IPv6 address
B. It requires either manual or DHCPv6 based address assignment for IPv6 host.
C. It helps ensure end-to-end address transparency and scalability
D. A state or bindings are created on every unique translation
E. it conserves IPV4 addresses
Correct Answer: BDE
QUESTION 29
Which two options are components of a dual stack?(choose two)
A. EIGRP
B. OSPF
C. IPV6 traffic
D. IPv4 traffic
E. layer 3 switch
F. layer 2 switch
Correct Answer: CD
QUESTION 30
Which technology uses the many-to-one method of mapping IP addresses?
A. static NAT
B. dynamic NAT
C. NAT-PT
D. PAT
Correct Answer: D
QUESTION 31
Which three statements about IPv6 EIGRP are true? 300-101 dumps (Choose Three)
A. EIGRP neighbor relationships are formed using the link-local address
B. EIGRP neighbor relationships can be formed only on the configured IPv6 address.
C. It supports ELM-64 addresses only.
D. EIGRP route advertisement is configured under the interface configuration
E. An IPv6 EIGRP router ID is required.
F. EIGRP route advertisement is configured under the ipv6 router eigrp configuration
Correct Answer: ADE
QUESTION 32
A network engineer is working on the network topology and executes the command no ip split- horizon on interface S0/0 of the hum router. What is the result of this command?
A. A routing loop is created.
B. Each of the spoke routers can see the routes that are advertised from the other spoke routers
C. The Spoke routers can see the routes that are advertised by the hub router
D. The hub router can see the routes that are advertised by the spoke routers
Correct Answer: B
QUESTION 33
All interfaces on each router are participating in the EIGRP 100 process. Interface Loopback 2 on HQR2 is currently in shutdown mode. An engineer issues the eigrp stub command on router BR1.
Which statements about the query messages sent from router HQ-R2 for a route to reach the 12.12.12.12/32 network is true?
A. Router HQ-R2 sends a query message to the feasible successor for a route to 12.12.12.12/32 network.
B. BR1 receives query messages from HQ-R2 for a route to 12.12.12.12/32 network
C. Router HQ-R1 receives query messages from HQ-R2 for a route to 12.12.12.12/32 network.
D. Router HQ-R1 and BR1 receives query messages from HQ-R2 for a route to 12.12.12/32 network.
Correct Answer: C
QUESTION 34
Drag and Drop
DMVPN
Select and Place:
Correct Answer:
Why Choose Lead 4 pass?
leads4pass is the best provider of IT learning materials and the right choice for you to pass Cisco 300-101 exam. Other brands started earlier, but the questions are not the newest and the price is relatively expensive. leads4pass provide the latest real and cheapest questions and answers, help you pass Cisco 300-101 exam easily at first try.
The Following Are Some Reviews From Our Customers:
You can click here to have a review about us: https://www.resellerratings.com/store/leads4pass
Practice for your Cisco 300–101 exam with the help of leads4pass, new Cisco CCDP 300-101 dumps pdf practice materials and study guides free download. Useful latest Cisco CCDP https://www.leads4pass.com/300-101.html dumps pdf training resources which are the best for clearing 300-101 exam test, and to get certified by Cisco CCDP. 100% success and guarantee to pass Cisco 300-101 exam.
High quality Cisco CCDP 300-101 dumps vce youtube:
https://youtu.be/QIdkjYjrUl0